侧面封边对玻璃纤维增强环氧树脂基复合材料吸湿规律的影响

采用称量法和排水法联合,研究了侧面封边和未封边单向玻璃纤维增强环氧树脂基复合材料层合板试件的吸湿量和体积变化率与浸泡时间的关系,结果显示,复合材料侧面吸湿的速度远大于表面吸湿速度;侧面封边复合材料试件的饱和吸湿量为1.30％,而未封边试件的为2.26％,即与侧面封边试件相比,未封边试件的饱和吸湿量(质量比)增加了73....     

超电磁材料与未来隐身技术

阐述传统隐身技术的理念和超电磁材料的基本概念与基本特性,超电磁材料是一种具有天然材料所不具备的超常物理性质的人工复合结构或复合材料,其性质往往不主要决定于构成材料的成分与本征性质,而决定于其中的人工结构.分析、说明了超电磁材料隐身技术的基本原理、设计思路与理解方法.指出了目前超电磁材料隐身技术的研究进展,最后得出未来超电磁材料应用于隐身技术具有良好潜在应用前景的结论.     

纤维缠绕复合材料夹芯圆柱体高应变率压缩吸能机理

为研究纤维缠绕复合材料夹芯圆柱体吸能元件在高应变率冲击压缩载荷作用下的变形损伤模式和能量吸收机理,采用ABAQUS商用有限元软件和分离式Hopkinson压杆装置开展数值模拟分析和试验验证研究。对比分析宏观力学响应规律和微观损伤破坏机理,可知吸能结构元件在高应变率压缩载荷下的力学响应具有典型的弹塑性特征,内部芯材主要产生压缩塑性损伤,而表层复合材料沿环向产生拉伸断裂破坏。研究表明,该吸能元件冲击压缩吸能特性优异,可满足水下结构平台的冲击防护和浮力储备要求。     

氘-金碰撞中J/ψ产生截面随x_F变化的研究

在不同碰撞质心能量下对氘-金(d-Au)碰撞中J/ψ核吸收效应进行了研究,结果表明,在不同碰撞质心能量下J/ψ核吸收截面随动量分数xF变化趋势明显不同。利用以上结论,计算了美国相对论重离子对撞机(RHIC)能量下J/ψ在氘-金(d-Au)碰撞中与质子-质子(p-p)碰撞中的产生截面比,并与实验数据比较发现,理论结果能很好的解释实验现象。最后,为欧洲大强子对撞机(LHC)实验作了理论预言,理论结果将为即将运行的LHC实验所检验。     

Development of cost effective personnel armour through structural hybridization

The objective of the present study is to develop cost effective thermoplastic hybrid laminate using Dyneema® HB50 and Tensylon®HSBD 30A through structural hybridization method. Laminates having 20 mm thickness were fabricated and subjected to 7.62 × 39 mm mild steel core projectile with an impact velocity of 730 ± 10 ms⁻¹. Parameters such as energy absorption, back face deformation and rate of back face deformation were measured as a function of hybridization ratio. It was observed that hybrid laminate with 50:50 ratio (w/w) of Tensylon® and Dyneema® with Tensylon® as front face showed 200% more energy absorption when compared to 100% Tensylon® laminate and showed equal energy absorption as that of expensive 100% Dyneema® laminate. Moreover, hybrid laminate with TD50:50 ratio showed 40% lower in terms of final back face deformation than Dyneema® laminate. Rate of back face deformation was also found to be slow for hybrid laminate as compared to Dyneema® laminate. Dynamic mechanical analysis showed that, Tensylon® laminate has got higher stiffness and lower damping factor than Dyneema® and hybrid laminates. The interface between Tensylon® and Dyneema® layers was found to be separating during the penetration process due to the poor interfacial bonding. Failure behaviour of laminates for different hybridization ratios were studied by sectioning the impacted laminates. It was observed that, the Tensylon® laminate has undergone shear cutting of fibers as major failure mode whereas the hybrid laminate showed shear cutting followed by tensile stretching, fiber pull out and delamination. These inputs are highly useful for body armour applications to design cost effective armour with enhanced performance.     

复合材料修补金属裂损结构吸湿老化的试验与有限元分析

暴露在湿热环境中的复合材料修补金属裂损结构易吸湿老化,导致该结构性能下降,服役寿命缩短。为研究吸湿性对复合材料修补金属裂损结构修补效果和耐久性的影响,利用试验方法分析了吸湿性对复合材料胶补金属裂损结构及胶黏剂力学性能的影响;利用有限元方法评估了吸湿性对复合材料胶补金属裂损结构试验件修补效果和耐久性的影响。研究结果表明:吸湿后含穿透双边裂纹铝合金板玻璃纤维单面胶补试验件的疲劳裂纹扩展寿命和极限载荷的平均值分别下降为吸湿前的71%和90%;吸湿造成拉伸条件下复合材料胶补金属裂损结构胶层失效模式由内聚破坏为主转变为界面破坏为主;在"湿-热"老化30天后,E44/聚酰胺环氧树脂胶黏剂试验件吸水饱和,弹性模量下降为未老化前的40%,塑性应变超过了总应变的25%;有限元分析发现胶层损伤受吸湿影响明显,吸湿性加速了胶层损伤,且裂纹长度越长,加速作用越明显;同时吸湿使得裂纹尖端的J积分值急剧增大,导致修补结构的疲劳裂纹扩展寿命缩短,裂纹长度越长,吸湿性对于复合材料胶接修补效果的危害越严重。     

纤维缠绕复合材料约束球形浮力芯材准静态压缩吸能机制

针对海洋工程平台的防护吸能和浮力储备需求,设计一种纤维缠绕复合材料约束球形浮力芯材吸能结构。为分析其变形损伤特征和能量耗散机理,通过ABAQUS有限元软件和万能材料试验机开展数值模拟分析和试验验证研究。通过力学响应特征和损伤破坏模式分析可知,结构吸能设计的关键在于表层和芯材的泊松比匹配。芯材主要通过塑性压缩损伤和剪切断裂破坏吸收能量,而表层吸能则主要通过环向的花瓣形拉伸断裂破坏。研究表明,该型结构单元压缩吸能特性优异,可实现海洋工程结构平台的防护吸能和浮力储备要求。     

雷达波吸收剂的研究进展

系统叙述了铁氧体、金属微粒、多晶铁纤维、纳米吸收剂和手征性吸收剂等吸收剂近年的研究发展状况,预测了吸收剂研究的未来发展趋势。     

吸湿环境对石英纤维增强环氧树脂面板/PMI泡沫夹层结构复合材料吸湿行为的影响

研究了不同温度、湿度环境下,夹层结构石英纤维增强环氧树脂面板/PMI泡沫夹层结构复合材料及其芯材和面板的吸湿规律。将石英纤维增强环氧树脂面板、PMI泡沫、复合材料面板/PMI泡沫夹层结构试样在不同吸湿环境中进行吸湿处理后,对其吸湿行为进行分析。结果表明:浸水环境下面板、PMI泡沫、PMI泡沫夹层结构复合材料都表现出更为严重的吸湿行为;在潮湿环境中,50℃至70℃范围内,温度越高,试样在吸湿过程中的质量损失越多,最终的饱和吸湿率越小;在60℃以内的潮湿环境中,PMI泡沫夹层结构复合材料的饱和吸湿率可以通过相同环境下面板复合材料和PMI泡沫的吸湿率进行预测。     

Performance study of jute-epoxy composites/sandwiches under normal ballistic impact

This study is undertaken to explore the use of natural fiber Jute-epoxy (JE), Jute-epoxy-rubber (JRE) sandwich composite for ballistic energy absorption. Energy absorbed and residual velocities for these composites are evaluated analytically and through Finite Element Analysis (FEA). FE analysis of JE plates is carried out for different thicknesses (3, 5, 10 and 15 mm). JE plates and JRE sandwiches having the same thickness (15 mm) are fabricated and tested to measure residual velocity and energy absorbed. The analytical results are found to agree well with the results of FE analysis with a maximum error of 9%. The study on JE composite plate reveals that thickness influences the energy absorption. Experimental and FE analysis study showed that JRE sandwiches have better energy absorption than JE plates. Energy absorption of a JRE sandwich is about 71% greater than JE plates. Damages obtained from FEA and testing are in good agreement. SEM analysis confirms composites failed by fiber rupture and fragmentation.